jumbo6 - Online in the Cloud

PROGRAM:

NAME

jumbo6 - A security assessment tool for attack vectors based on IPv6 jumbograms

SYNOPSIS

jumbo6 [-i INTERFACE] [-S LINK_SRC_ADDR] [-D LINK-DST-ADDR] [-s SRC_ADDR[/LEN]] [-d
DST_ADDR] [-A HOP_LIMIT] [-H HBH_OPT_HDR_SIZE] [-U DST_OPT_U_HDR_SIZE] [-y FRAG_SIZE] [-u
DST_OPT_HDR_SIZE] [-q IPV6_LENGTH] [-Q JUMBO_LENGTH] [-P PAYLOAD_SIZE] [-l] [-z SECONDS]
[-v] [-h]

DESCRIPTION

jumbo6 allows the assessment of IPv6 implementations with respect to attack vectors based
on IPv6 jumbograms. It is part of the SI6 Networks' IPv6 Toolkit : a security assessment
suite for the IPv6 protocols.

This tool has only one mode of operation: active mode. In active mode, the tool sends IPv6
jumbograms to the specified target, and informs the user of any received ICMPv6 error
messages (typically "ICMPv6 Parameter Problem" error messages).

OPTIONS

jumbo6 takes its parameters as command-line options. Each of the options can be specified
with a short name (one character preceded with the hyphen character, as e.g. "-i") or with
a long name (a string preceded with two hyphen characters, as e.g. "--interface").

jumbo6 supports IPv6 Extension Headers, including the IPv6 Fragmentation Header, which
might be of use to circumvent layer-2 filtering and/or Network Intrusion Detection Systems
(NIDS). However, IPv6 extension headers are not employed by default, and must be
explicitly enabled with the corresponding options.

-i INTERFACE, --interface INTERFACE
This option specifies the network interface that the tool will use. If the
destination address ("-d" option) is a link-local address, the interface must be
explicitly specified. The interface may also be specified along with a destination
address, with the "-d" option.

-S SRC_LINK_ADDR, --src-link-address SRC_LINK_ADDR

This option specifies the link-layer Source Address of the probe packets. If left
unspecified, the link-layer Source Address of the packets is set to the real
link-layer address of the network interface.

-D DST_LINK_ADDR, --dst-link-address DST_LINK_ADDR

This option specifies the link-layer Destination Address of the probe packets
(currently, only Ethernet is supported). By default, the link-layer Destination
Address is automatically set to the link-layer address of the destination host (for
on-link destinations) or to the link-layer address of the first-hop router.

-s SRC_ADDR, --src-address SRC_ADDR

This option specifies the IPv6 source address (or IPv6 prefix) to be used for the
Source Address of the outgoing packets. If an IPv6 prefix is specified, the IPv6
Source Address of the outgoing packets will be randomized from that prefix.

-d DST_ADDR, --dst-address DST_ADDR

This option specifies the IPv6 Destination Address of the target node. This option
cannot be left unspecified.

--hop-limit, -A

This option specifies the Hop Limit to be used for the IPv6 packets. By default,
the Hop Limit is randomized.

-y SIZE, --frag-hdr SIZE

This option specifies that the resulting packet must be fragmented. The fragment
size must be specified as an argument to this option.

-u HDR_SIZE, --dst-opt-hdr HDR_SIZE

This option specifies that a Destination Options header is to be included in the
resulting packet. The extension header size must be specified as an argument to
this option (the header is filled with padding options). Multiple Destination
Options headers may be specified by means of multiple "-u" options.

-U HDR_SIZE, --dst-opt-u-hdr HDR_SIZE

This option specifies a Destination Options header to be included in the
"unfragmentable part" of the resulting packet. The header size must be specified as
an argument to this option (the header is filled with padding options). Multiple
Destination Options headers may be specified by means of multiple "-U" options.
This option is only valid if the "-y" option is specified (as the concept of
"unfragmentable part" only makes sense when fragmentation is employed).

-H HDR_SIZE, --hbh-opt-hdr HDR_SIZE

This option specifies that a Hop-by-Hop Options header is to be included in the
resulting packet. The header size must be specified as an argument to this option
(the header is filled with padding options). Multiple Hop-by-Hop Options headers
may be specified by means of multiple "-H" options.

--ipv6-length, -q

This option specifies the value that the "Total Length" field of the IPv6 header
should be set to. If this option is left unspecified, the "Total Length" field is
set to 0, as required by the IPv6 jumbograms specification.

--jumbo-length, -Q

This option specifies the value to which the "Jumbo Payload Length" field of the
Jumbo Payload option should be set. If this option is left unspecified, the "Jumbo
Payload Length" field is set according to the real size of the jumbo payload (see
the "-p" option).

--payload-size, -P

This options specifies the size of the jumbo payload. If left unspecified, the
payload size is set to 0.

--loop, -l

This option instructs the jumbo6 tool to send periodic IPv6 jumbograms to the
victim node. The amount of time to pause between sending IPv6 jumbograms can be
specified by means of the "-z" option, and defaults to 1 second.

--sleep, -z

This option specifies the amount of time to pause between sending IPv6 jumbograms
(when the "--loop" option is set). If left unspecified, it defaults to 1 second.

--verbose, -v

This option instructs the jumbo6 tool to be verbose. When the option is set twice,
the tool is "very verbose", and the tool also informs which packets have been
accepted or discarded as a result of applying the specified filters.

--help, -h

Print help information for the jumbo6 tool.

EXAMPLES

The following sections illustrate typical use cases of the jumbo6 tool.

Example #1

# jumbo6 -s fc00:1::/64 -d fc00:1::1 -P 100

Send an IPv6 jumbogram to the host fc00:1::1. The IPv6 Source Address will be randomly
selected from the prefix fc00:1::/64, and a the payload of 100 bytes is included in the
packet.

Use jumbo6 online using onworks.net services