EnglishFrenchSpanish

Ad


OnWorks favicon

cgminer - Online in the Cloud

Run cgminer in OnWorks free hosting provider over Ubuntu Online, Fedora Online, Windows online emulator or MAC OS online emulator

This is the command cgminer that can be run in the OnWorks free hosting provider using one of our multiple free online workstations such as Ubuntu Online, Fedora Online, Windows online emulator or MAC OS online emulator

PROGRAM:

NAME


cgminer - multi-threaded multi-pool GPU, FPGA and CPU bitcoin miner.

SYNOPSIS


cgminer [-DlmpPqUTouOchnV]

DESCRIPTION


multi-threaded multi-pool GPU, FPGA and CPU bitcoin miner. Built with avalon avalon2
avalon4 bflsc bitfury cointerra drillbit hashfast icarus klondike mining support.

OPTIONS


Options for both config file and command line:
--anu-freq <arg>
Set AntminerU1/2 frequency in MHz, range 125-500 (default: 250.0)

--api-allow <arg>
Allow API access only to the given list of [G:]IP[/Prefix] addresses[/subnets]

--api-description <arg>
Description placed in the API status header, default: cgminer version

--api-groups <arg>
API one letter groups G:cmd:cmd[,P:cmd:*...] defining the cmds a groups can use

--api-listen
Enable API, default: disabled

--api-mcast
Enable API Multicast listener, default: disabled

--api-mcast-addr <arg>
API Multicast listen address

--api-mcast-code <arg>
Code expected in the API Multicast message, don't use '-'

--api-mcast-des <arg>
Description appended to the API Multicast reply, default: ''

--api-mcast-port <arg>
API Multicast listen port (default: 4028)

--api-network
Allow API (if enabled) to listen on/for any address, default: only 127.0.0.1

--api-port <arg>
Port number of miner API (default: 4028)

--api-host <arg>
Specify API listen address, default: 0.0.0.0

--au3-freq <arg>
Set AntminerU3 frequency in MHz, range 100-250 (default: 225.0)

--au3-volt <arg>
Set AntminerU3 voltage in mv, range 725-850, 0 to not set (default: 775)

--avalon-auto
Adjust avalon overclock frequency dynamically for best hashrate

--avalon-cutoff <arg>
Set avalon overheat cut off temperature (default: 60)

--avalon-fan
Set fanspeed percentage for avalon, single value or range (default: 20-100)

--avalon-freq
Set frequency range for avalon-auto, single value or range

--avalon-options <arg>
Set avalon options baud:miners:asic:timeout:freq:tech

--avalon-temp <arg>
Set avalon target temperature (default: 50)

--avalon2-freq
Set frequency range for Avalon2, single value or range, step: 25

--avalon2-voltage
Set Avalon2 core voltage, in millivolts, step: 125

--avalon2-fan
Set Avalon2 target fan speed

--avalon2-cutoff <arg>
Set Avalon2 overheat cut off temperature (default: 98)

--avalon2-fixed-speed
Set Avalon2 fan to fixed speed

--avalon2-polling-delay <arg>
Set Avalon2 polling delay value (ms) (default: 20)

--avalon4-automatic-voltage
Automatic adjust voltage base on module DH

--avalon4-voltage
Set Avalon4 core voltage, in millivolts, step: 125

--avalon4-freq
Set frequency for Avalon4, 1 to 3 values, example: 445:385:370

--avalon4-fan
Set Avalon4 target fan speed range

--avalon4-temp <arg>
Set Avalon4 target temperature (default: 42)

--avalon4-cutoff <arg>
Set Avalon4 overheat cut off temperature (default: 65)

--avalon4-polling-delay <arg>
Set Avalon4 polling delay value (ms) (default: 20)

--avalon4-ntime-offset <arg>
Set Avalon4 MM ntime rolling max offset (default: 4)

--avalon4-aucspeed <arg>
Set Avalon4 AUC IIC bus speed (default: 400000)

--avalon4-aucxdelay <arg>
Set Avalon4 AUC IIC xfer read delay, 4800 ~= 1ms (default: 19200)

--balance
Change multipool strategy from failover to even share balance

--benchfile <arg>
Run cgminer in benchmark mode using a work file - produces no shares

--benchfile-display
Display each benchfile nonce found

--benchmark
Run cgminer in benchmark mode - produces no shares

--bflsc-overheat <arg>
Set overheat temperature where BFLSC devices throttle, 0 to disable (default: 85)

--bitburner-voltage <arg>
Set BitBurner (Avalon) core voltage, in millivolts

--bitburner-fury-voltage <arg>
Set BitBurner Fury core voltage, in millivolts

--bitburner-fury-options <arg>
Override avalon-options for BitBurner Fury boards baud:miners:asic:timeout:freq

--bxf-bits <arg>
Set max BXF/HXF bits for overclocking (default: 54)

--bxf-debug <arg>
BXF: Debug all USB I/O, > is to the board(s), < is from the board(s) (default: 0)

--bxf-temp-target <arg>
Set target temperature for BXF/HXF devices (default: 82)

--bxm-bits <arg>
Set BXM bits for overclocking (default: 54)

--btc-address <arg>
Set bitcoin target address when solo mining to bitcoind (mandatory)

--btc-sig <arg>
Set signature to add to coinbase when solo mining (optional)

--compact
Use compact display without per device statistics

--cta-load <arg>
Set load for CTA devices, 0-255 range (default: 0)

--ps-load <arg>
Set power supply load for CTA devices, 0-100 range (default: 0)

--debug|-D
Enable debug output

--disable-rejecting
Automatically disable pools that continually reject shares

--drillbit-options <arg>
Set drillbit options <int|ext>:clock[:clock_divider][:voltage]

--drillbit-auto <arg>
Enable drillbit automatic tuning <every>:[<gooderr>:<baderr>:<maxerr>]

--fix-protocol
Do not redirect to stratum protocol from GBT

--hfa-hash-clock <arg>
Set hashfast clock speed (default: 550)

--hfa-fail-drop <arg>
Set how many MHz to drop clockspeed each failure on an overlocked hashfast device
(default: 10)

--hfa-fan
Set fanspeed percentage for hashfast, single value or range (default: 10-85)

--hfa-name <arg>
Set a unique name for a single hashfast device specified with --usb or the first
device found

--hfa-noshed
Disable hashfast dynamic core disabling feature

--hfa-options <arg>
Set hashfast options name:clock (comma separated)

--hfa-temp-overheat <arg>
Set the hashfast overheat throttling temperature (default: 95)

--hfa-temp-target <arg>
Set the hashfast target temperature (0 to disable) (default: 88)

--hro-freq
Set the hashratio clock frequency

--hotplug <arg>
Seconds between hotplug checks (0 means never check)

--klondike-options <arg>
Set klondike options clock:temptarget

--load-balance
Change multipool strategy from failover to quota based balance

--log|-l <arg>
Interval in seconds between log output (default: 5)

--lowmem
Minimise caching of shares for low memory applications

--monitor|-m <arg>
Use custom pipe cmd for output messages

--nfu-bits <arg>
Set nanofury bits for overclocking, range 32-63 (default: 50)

--net-delay
Impose small delays in networking to not overload slow routers

--no-submit-stale
Don't submit shares if they are detected as stale

--osm-led-mode <arg>
Set LED mode for OneStringMiner devices (default: 4)

--pass|-p <arg>
Password for bitcoin JSON-RPC server

--per-device-stats
Force verbose mode and output per-device statistics

--protocol-dump|-P
Verbose dump of protocol-level activities

--quiet|-q
Disable logging output, display status and errors

--quota|-U <arg>
quota;URL combination for server with load-balance strategy quotas

--real-quiet
Disable all output

--rock-freq <arg>
Set RockMiner frequency in MHz, range 125-500 (default: 270.0)

--rotate <arg>
Change multipool strategy from failover to regularly rotate at N minutes

--round-robin
Change multipool strategy from failover to round robin on failure

--sched-start
Set a time of day in HH:MM to start mining (a once off without a stop time)

--sched-stop
Set a time of day in HH:MM to stop mining (will quit without a start time)

--sharelog
Append share log to file

--shares <arg>
Quit after mining N shares (default: unlimited)

--socks-proxy <arg>
Set socks4 proxy (host:port)

--suggest-diff <arg>
Suggest miner difficulty for pool to user (default: none)

--syslog
Use system log for output messages (default: standard error)

--temp-cutoff
Temperature where a device will be automatically disabled, one value or comma
separated list (default: 0)

--text-only|-T
Disable ncurses formatted screen output

--url|-o <arg>
URL for bitcoin JSON-RPC server

--usb <arg>
USB device selection

--user|-u <arg>
Username for bitcoin JSON-RPC server

--userpass|-O <arg>
Username:Password pair for bitcoin JSON-RPC server

--verbose
Log verbose output to stderr as well as status output

--widescreen
Use extra wide display without toggling

--worktime
Display extra work time debug information

Options for command line only:
--config|-c <arg>
Load a JSON-format configuration file See example.conf for an example
configuration.

--default-config <arg>
Specify the filename of the default config file Loaded at start and used when
saving without a name.

--help|-h
Print this message

--ndevs|-n
Display all USB devices and exit

--version|-V
Display version and exit

Use cgminer online using onworks.net services


Free Servers & Workstations

Download Windows & Linux apps

  • 1
    wxPython
    wxPython
    A set of Python extension modules that
    wrap the cross-platform GUI classes from
    wxWidgets.. Audience: Developers. User
    interface: X Window System (X11), Win32 ...
    Download wxPython
  • 2
    packfilemanager
    packfilemanager
    This is the Total War pack file manager
    project, starting from version 1.7. A
    short introduction into Warscape
    modding: ...
    Download packfilemanager
  • 3
    IPerf2
    IPerf2
    A network traffic tool for measuring
    TCP and UDP performance with metrics
    around both throughput and latency. The
    goals include maintaining an active
    iperf cod...
    Download IPerf2
  • 4
    fre:ac - free audio converter
    fre:ac - free audio converter
    fre:ac is a free audio converter and CD
    ripper for various formats and encoders.
    It features MP3, MP4/M4A, WMA, Ogg
    Vorbis, FLAC, AAC, and Bonk format
    support, ...
    Download fre:ac - free audio converter
  • 5
    BotMan
    BotMan
    Write your chatbot logic once and
    connect it to one of the available
    messaging services, including Amazon
    Alexa, Facebook Messenger, Slack,
    Telegram or even yo...
    Download BotMan
  • 6
    gerbv  a Gerber (RS-274X) viewer
    gerbv a Gerber (RS-274X) viewer
    Gerbv is an open source Gerber file
    (RS-274X only) viewer. Gerbv lets you
    load several files on top of each other,
    do measurements on the displayed image,
    etc. ...
    Download gerbv a Gerber (RS-274X) viewer
  • 7
    Iometer
    Iometer
    I/O performance Analysis Tool.
    Audience: Developers, Information
    Technology, Science/Research, System
    Administrators. User interface: Win32
    (MS Windows). Progr...
    Download Iometer
  • More »

Linux commands

Ad