osmocom_spectrum_sense - Online in the Cloud

PROGRAM:

NAME

osmocom_spectrum_sense - GNU Radio application from OsmoSDR

SYNOPSIS

osmocom_spectrum_sense [options] min_freq max_freq

DESCRIPTION

GNU Radio application from OsmoSDR

OPTIONS

-h, --help
show this help message and exit

-a ARGS, --args=ARGS
Device args [default=]

-A ANTENNA, --antenna=ANTENNA
Select antenna where appropriate

-s SAMP_RATE, --samp-rate=SAMP_RATE
Set sample rate (bandwidth), minimum by default

-g GAIN, --gain=GAIN
Set gain in dB (default is midpoint)

--tune-delay=SECS
Time to delay (in seconds) after changing frequency [default=0.25]

--dwell-delay=SECS
Time to dwell (in seconds) at a given frequency [default=0.25]

-b Hz, --channel-bandwidth=Hz
Channel bandwidth of fft bins in Hz [default=6250.0]

-q dB, --squelch-threshold=dB
Squelch threshold in dB [default=none]

-F FFT_SIZE, --fft-size=FFT_SIZE
Specify number of FFT bins [default=samp_rate/channel_bw]

--real-time
Attempt to enable real-time scheduling

Device specification

You can specify the source or sink device using a comma separated string of argument=value
pairs. The always-up-to-date block documentation with examples is available ​right here.

FCD Source

Argument
Notes

fcd=<device-index>
0-based device identifier, optional

device=hw:2
overrides the audio device

type=2 selects the dongle type, 1 for Classic, 2 for Pro+

The "device" argument overrides the audio device used by the underlying driver to access
the dongle's IQ sample stream.

The "type" argument selects the dongle type, 1 for Classic, 2 for Pro+.

OsmoSDR Source

Argument
Notes

osmosdr=<device-index>
0-based device identifier

buffers=<number-of-buffers>
Default is 32

buflen=<length-of-buffer>
Default is 256kB, must be multiple of 512

RTL-SDR Source

Argument
Notes

rtl=<device-index>
0-based device identifier OR serial number

rtl_xtal=<frequency>
Frequency (Hz) used for the RTL chip, accepts eng notation

tuner_xtal=<frequency>
Frequency (Hz) used for the tuner chip, accepts eng notation

buffers=<number-of-buffers>
Default is 32

buflen=<length-of-buffer>
Default is 256kB, must be multiple of 512

direct_samp=0|1|2
Enable direct sampling mode on the RTL chip. 0: Disable, 1: use I channel, 2: use Q
channel

offset_tune=0|1
Enable offset tune mode for E4000 tuners

NOTE: use rtl_eeprom -s to program your own serial number to the device

NOTE: if you don't specify rtl_xtal/tuner_xtal, the underlying driver will use 28.0MHz

RTL-SDR TCP Source

Argument
Notes

rtl_tcp=<hostname>:<port>
hostname defaults to "localhost", port to "1234"

psize=<payload-size>
Default is 16384 bytes

direct_samp=0|1|2
Enable direct sampling mode on the RTL chip 0=Off, 1=I-ADC input enabled, 2=Q-ADC
input enabled

offset_tune=0|1
Enable offset tune mode for E4000 tuners

Miri Source

Argument
Notes

miri=<device-index>
0-based device identifier

buffers=<number-of-buffers>
Default is 32

UHD Source / Sink

Argument Notes

uhd Use this argument without a value

nchan=<channel-count>
For multichannel USRP configurations use the subdev parameter to specify stream
mapping

subdev=<subdev-spec>
Examples: "A:0", "B:0", "A:0 B:0" when nchan=2. Refer original ettus documentation
on this

lo_offset=<frequency>
Offset frequency in Hz, must be within daughterboard bandwidth. Accepts eng
notation

Additional argument/value pairs will be passed to the underlying driver, for more
information see ​specifying the subdevice and ​common device identifiers in the Ettus
documentation.

bladeRF Source / Sink

Argument
Notes

bladerf[=0]
0-based device identifier (optional)

fw='/path/to/the/firmware.img'
program MCU firmware from given file. usually not needed. power cycle required.

fpga='/path/to/the/bitstream.rbf'
load FPGA bitstream from given file. required only at first run at the moment.

HackRF Source / Sink

Argument
Notes

hackrf Use this argument without a value

buffers=<number-of-buffers>
Default is 32

Only the first device found may be used at the moment because of libhackrf limitation.

Transmit support has been verified by using the crc-mmbTools DAB sdr transmitter.

IQ File Source

Argument
Notes

file=<path-to-file-name>

freq=<frequency>
Center frequency in Hz, accepts eng notation

rate=<sampling-rate>
Mandatory, in samples/s, accepts eng notation

repeat=true|false
Default is true

throttle=true|false
Throttle flow of samples, default is true

Use osmocom_spectrum_sense online using onworks.net services