OnWorks favicon

digitemp_DS9097U - Online in the Cloud

Run digitemp_DS9097U in OnWorks free hosting provider over Ubuntu Online, Fedora Online, Windows online emulator or MAC OS online emulator

This is the command digitemp_DS9097U that can be run in the OnWorks free hosting provider using one of our multiple free online workstations such as Ubuntu Online, Fedora Online, Windows online emulator or MAC OS online emulator



digitemp - program to read from 1-wire temperature sensors.


digitemp [options]


DigiTemp uses the Dallas 1-wire bus to read temperatures from digital sensors attached to
a serial port adapter. It handles initializing the bus, searching for attached devices,
reading devices and custom log strings. It supports the following temperature devices:
DS1820, DS18S20, DS18B20, DS1822

It also handles the DS2406 1-wire hub switches, and DS2422 and DS2423 counters.

DigiTemp uses either the DS9097 passive serial port adapter, or the DS2480B based DS9097U
adapter. 1-wire adapters from ibuttonlink.com, such as the Link45 are also supported.


At least 1 action must be given, along with some optional arguments. Actions are one (and
only on) of the -w -t -a -w options

-h, -? Show summary of options.

-v Show verbose output.

-i Initialize .digitemprc file, search the bus for all supported devices.

-I Initialize .digitemprc file, search the bus for all supported devices, store
devices in sorted serial # order.

-w Walk the full device tree and display the serial number and type of all devices
detected on the bus.

-s /dev/ttyS0
Set serial port to use. Make sure you have permission to access this port. For USB
operation pass USB instead of /dev/ttySX

-l /var/log/temperature
Send output to logfile, the output format is defined by the .B -o command

-c digitemp.conf
Set digitemp configuration file. The default is .digitemprc in the current

-r 1000
Read delay in ms. This sets the amount of time to wait between sending the
temperature conversion command and reading the result. The DS18S20 takes about
750mS to do the temperature conversion. Default is 1000mS (1 sec).

-t # Read sensor number #, the # depends on the order of the sensors in the .digitemprc

-q Quiet output, no copyright banner.

-a Read all sensors.

-A Treat DS2438 as A/D converter, output raw voltages and currents.

-d 5 Delay between samples (in seconds).

-n 50 Number of times to repeat the command.

-O"counter format string"
See Counter Format below.

-o [1..3] ["output format string"]
See Temperature Format below.

-H"Humidity format string"
See Humidity Format below.

Temperature Format

The temperature format can be either a numeric value, or a string. The numeric values
select pre-configured output formats:

1 = One line per sensor, time, C, F (default)
2 = One line per sample, elapsed time, temperature in C
3 = Same as #2, except temperature is in F

#2 and #3 have the data separated by tabs, suitable for import into a spreadsheet or other
graphing software.

The format string uses strftime tokens plus 5 special ones for DigiTemp:

%s for sensor #

%C for centigrade

%F for fahrenheit

%R to output the hex serial number

%N for seconds since Epoch.

The case of the token is important! The default format string is: "%b %d %H:%M:%S Sensor
%s C: %.2C F: %.2F" which gives you an output of: May 24 21:25:43 Sensor 0 C: 23.66 F:

The DS2438 sensor can be used for a variety of things. It includes a temperature sensor
and A/D converter. DigiTemp defaults to using it as a humidity sensor. The raw voltages
and currents can be displayed by passing the -A argument

When the -o2 or -o3 log options are used the attached DS2438's temperatures will be output
without the humidity.

Counter Format String

The counter format string is similar, adding these tokens:

%n is the counter #, which depends on its position in the .digitemprc file

%C is the count in decimal.

Humidity Format String

The Humidity format string is the same as the temperature format string with the addition
of this format specifier:

%h is the humidity in 0-100%

Use digitemp_DS9097U online using onworks.net services

Free Servers & Workstations

Download Windows & Linux apps

  • 1
    ExpressLuke GSI
    ExpressLuke GSI
    This SourceForge download page was to
    grant users to download my source built
    GSIs, based upon phhusson's great
    work. I build both Android Pie and
    Android 1...
    Download ExpressLuke GSI
  • 2
    PyQt is the Python bindings for
    Digia's Qt cross-platform
    application development framework. It
    supports Python v2 and v3 and Qt v4 and
    Qt v5. PyQt is avail...
    Download PyQt
  • 3
    Gambas3* coding tools and examples for
    use in SMB or other organizations that
    make internal programs. E.g. from
    database fields to class sourcecode with
    Download garlic3
  • 4
    Sardi is a complete restyling and
    optimisation of svg code. 6 choices for
    your applications and 10 kind of folders
    to use in your file manager. The sardi
    Download Sardi
  • 5
    LMMS Digital Audio Workstation
    LMMS Digital Audio Workstation
    LMMS is a free cross-platform software
    which allows you to produce music with
    your computer. If you like this project
    consider getting involved in the project
    Download LMMS Digital Audio Workstation
  • 6
    FreeRTOS Real Time Kernel (RTOS)
    FreeRTOS Real Time Kernel (RTOS)
    FreeRTOS is a market-leading real-time
    operating system (RTOS) for
    microcontrollers and small
    microprocessors. Distributed freely
    under the MIT open source lice...
    Download FreeRTOS Real Time Kernel (RTOS)
  • 7
    Avogadro is an advanced molecular
    editor designed for cross-platform use
    in computational chemistry, molecular
    modeling, bioinformatics, materials
    science and ...
    Download Avogadro
  • More »

Linux commands