EnglishFrenchSpanish

OnWorks favicon

na6 - Online in the Cloud

Run na6 in OnWorks free hosting provider over Ubuntu Online, Fedora Online, Windows online emulator or MAC OS online emulator

This is the command na6 that can be run in the OnWorks free hosting provider using one of our multiple free online workstations such as Ubuntu Online, Fedora Online, Windows online emulator or MAC OS online emulator

PROGRAM:

NAME


na6 - A security assessment tool for attack vectors based on ICMPv6 Neighbor Advertisement
messages

SYNOPSIS


na6 [-i INTERFACE] [-s SRC_ADDR[/LEN]] [-d DST_ADDR] [-S LINK_SRC_ADDR] [-y FRAG_SIZE] [-u
DST_OPT_HDR_SIZE] [-U DST_OPT_U_HDR_SIZE] [-H HBH_OPT_HDR_SIZE] [-D LINK-DST-ADDR] [-t
TARGET_ADDR[/LEN]] [-r] [-c] [-o] [-E LINK_ADDR] [-e] [-j PREFIX[/LEN]] [-k PREFIX[/LEN]]
[-J LINK_ADDR] [-K LINK_ADDR] [-w PREFIX[/LEN]] [-b PREFIX[/LEN]] [-g PREFIX[/LEN]] [-B
LINK_ADDR] [-G LINK_ADDR] [-W PREFIX[/LEN]] [-F N_SOURCES] [-T N_TARGETS] [-L | -l] [-z]
[-v] [-V] [-h]

DESCRIPTION


na6 allows the assessment of IPv6 implementations with respect to a variety of attack
vectors based on ICMPv6 Neighbor Advertisement messages. It is part of the SI6 Networks'
IPv6 Toolkit: a security assessment suite for the IPv6 Protocols.

This tool has two modes of operation: active and passive. In active mode, the tool attacks
a specific target, while in passive mode the tool listens to traffic on the local network,
and launches an attack in response to such traffic. Active mode is employed if a
destination address (IPv6 Destination Address or Ethernet Destination Address) and a
Target Address are specified. Passive mode is employed if the "-L" option (or its long
counterpart "--listen") is set. If both an attack target and the "-L" option are set, the
attack is launched against the specified target, and then the tool enters passive mode to
respond incoming Neighbor Solicitation messages with Neighbor Advertisement (attack)
packets.

The tool supports filtering of incoming Neighbor Solicitation messages based on the
Ethernet Source Address, the Ethernet Destination Address, the IPv6 Source Address, the
IPv6 Destination Address, and the Neighbor Solicitation Target Address. There are two
types of filters: "block filters" and "accept filters". If any "block filter" is
specified, and the incoming Neighbor Solicitation message matches any of those filters,
the message is discarded (and thus no Neighbor Advertisements are sent in response). If
any "accept filter" is specified, incoming Neighbor Solicitation messages must match the
specified filters in order for the na6 tool to respond with Neighbor Advertisement
messages.

OPTIONS


na6 takes its parameters as command-line options. Each of the options can be specified
with a short name (one character preceded with the hyphen character, as e.g. "-i") or with
a long name (a string preceded with two hyphen characters, as e.g. "--interface").

Depending on the amount of information (i.e., options) to be conveyed into the Neighbor
Advertisements, it may be necessary for the na6 tool to split that information into more
than one Neighbor Advertisement message. Also, if the tool is instructed to flood the
victim with Neighbor Advertisements from different sources ("--flood-sources" option),
multiple packets may need to be generated. na6 supports IPv6 fragmentation, which may be
of use if a large amount of information needs to be conveyed within a single Neighbor
Advertisement message. However, IPv6 fragmentation is not enabled by default, and must be
explicitly enabled with the "-y" option.

-i INTERFACE, --interface INTERFACE
This option specifies the network interface that the tool will use. If the
destination address ("-d" option) is a link-local address, or the "listening"
("-L") mode is selected, the interface must be explicitly specified. The interface
may also be specified along with a destination address, with the "-d" option.

-s SRC_ADDR, --src-address SRC_ADDR

This option specifies the IPv6 source address (or IPv6 prefix) to be used for the
Source Address of the attack packets. If left unspecified, a random link-local
unicast address (fe80::/64) is selected.

If the "-T" ("--flood-targets") option is specified, this option includes an IPv6
prefix. See the description of the "-T" option for further information on how the
"-s" option is processed in that specific case.

-d DST_ADDR, --dst-address DST_ADDR

This option specifies the IPv6 Destination Address of the victim. If left
unspecified, but the Ethernet Destination Address is specified, the "all-nodes
link-local multicast" address (ff02::1) is selected as the IPv6 Destination
Address.

When operating in passive mode ("-L" option), the IPv6 Destination Address is
selected according to the IPv6 Source Address of the incoming Neighbor Solicitation
message. If the IPv6 Source Address of the Neighbor Solicitation is the unspecified
address (::), the "all-nodes link-local multicast" address (ff02::1) is used as the
IPv6 Destination Address. Otherwise, the IPv6 Source Address of the incoming
Neighbor Solicitation message is used as the IPv6 Destination Address of the
outgoing Neighbor Advertisement (attack) messages.

--hop-limit, -A

This option specifies the Hop Limit to be used for the Neighbor Advertisement
messages. It defaults to 255. Note that IPv6 nodes are required to check that the
Hop Limit of incoming Neighbor Advertisement messages is 255. Therefore, this
option is only useful to assess whether an IPv6 implementation fails to enforce the
aforementioned check.

-y SIZE, --frag-hdr SIZE

This option specifies that the resulting packet must be fragmented. The fragment
size must be specified as an argument to this option.

-u HDR_SIZE, --dst-opt-hdr HDR_SIZE

This option specifies that a Destination Options header is to be included in the
resulting packet. The extension header size must be specified as an argument to
this option (the header is filled with padding options). Multiple Destination
Options headers may be specified by means of multiple "-u" options.

-U HDR_SIZE, --dst-opt-u-hdr HDR_SIZE

This option specifies a Destination Options header to be included in the
"unfragmentable part" of the resulting packet. The header size must be specified as
an argument to this option (the header is filled with padding options). Multiple
Destination Options headers may be specified by means of multiple "-U" options.
This option is only valid if the "-y" option is specified (as the concept of
"unfragmentable part" only makes sense when fragmentation is employed).

-H HDR_SIZE, --hbh-opt-hdr HDR_SIZE

This option specifies that a Hop-by-Hop Options header is to be included in the
resulting packet. The header size must be specified as an argument to this option
(the header is filled with padding options). Multiple Hop-by-Hop Options headers
may be specified by means of multiple "-H" options.

-S SRC_LINK_ADDR, --src-link-address SRC_LINK_ADDR

This option specifies the link-layer Source Address of the Neighbor Advertisement
messages (this option is only valid for Ethernet interfaces). If left unspecified,
the link-layer Source Address is randomized.

When operating in passive mode, the link-layer Source Address is selected according
to the IPv6 Destination Address of the incoming Neighbor Solicitation message. If
the IPv6 Destination Address of the incoming Neighbor Solicitation message is a
multicast address (usually a solicited-node multicast address), the link-layer
Source Address is set to the address specified by the "-S" option (or to a random
address if the "-S" option was left unspecified). If the IPv6 Destination Address
of the incoming Neighbor Solicitation is not a multicast address (i.e., it is a
unicast address), the link-layer Source Address is set to the Ethernet Destination
Address of the incoming Neighbor Solicitation message.

-D DST_LINK_ADDR, --dst-link-address DST_LINK_ADDR

This option specifies the link-layer Destination Address of the Neighbor
Advertisement messages (this option is only valid for Ethernet interfaces). If left
unspecified, it is set to the "all-nodes link-local multicast" address (ff02::1).

When operating in passive mode, the link-layer Destination Address is set according
to the IPv6 Source Address of the incoming Neighbor Solicitation message. If the
IPv6 Source Address of the incoming Neighbor Solicitation message is the
unspecified address (::), the link-layer destination address is set to
"33:33:00:00:00:01" (the Ethernet multicast address corresponding to the IPv6 "all-
nodes link-local multicast" address). Otherwise, the link-layer Destination Address
is set to the link-layer Source Address of the incoming Neighbor Solicitation
message.

--router, -r

This option instructs the na6 tool to set the "R" (Router) bit in the Neighbor
Advertisement messages that it sends. The "R" bit indicates that the node sending
the message is a router. If left unspecified, the "R" bit is not set.

--solicited, -c

This option instructs the na6 tool to set the "S" ("Solicited") bit in the Neighbor
Advertisement messages that it sends. When operating in passive mode ("-L" option),
the "Solicited" flag is forced to 1 in all responses sent to unicast IPv6
addresses.

--override, -o

This option instructs the na6 tool to set the ‘O’ ("Override") bit in the Neighbor
Advertisement messages that it sends. If this option is left unspecified, the ‘O’
bit is not set.

--target, -t

This option specifies the IPv6 Target Address of the Neighbor Advertisement
messages.

If the "-T" ("--flood-targets") option is specified, this option specifies an IPv6
prefix in the form "-t prefix/prefixlen". See the description of the "-T" option
for further information on how the "-t" option is processed in that specific case.

--target-lla-opt, -E

This option specifies the contents of a target link-layer address option to be
included in the Neighbor Advertisement messages. If a single option is specified,
it is included in all the outgoing Neighbor Advertisement messages. If more than
one target link-layer address is specified (by means of multiple "-E" options), and
all the resulting options cannot be conveyed into a single Neighbor Advertisement
message, multiple Neighbor Advertisements will be sent as needed.

--add-tlla-opt, -e

This option instructs the na6 tool to include a target link-layer address option in
the Neighbor Advertisement messages that it sends. The target link-layer address
included in the option is the same as the Ethernet Source Address used for the
outgoing Neighbor Advertisement messages. The difference between this option and
the "-E" option is that the "-e" option does not specify the actual value of the
option, but just instructs the tool to include a target link-layer address option
(the actual value of the option is selected as explained before).

-j SRC_ADDR, --block-src SRC_ADDR

This option sets a block filter for the incoming packets, based on their IPv6
Source Address. It allows the specification of an IPv6 prefix in the form "-j
prefix/prefixlen". If the prefix length is not specified, a prefix length of "/128"
is selected (i.e., the option assumes that a single IPv6 address, rather than an
IPv6 prefix, has been specified).

-k DST_ADDR, --block-dst DST_ADDR

This option sets a block filter for the incoming Neighbor Solicitation messages,
based on their IPv6 Destination Address. It allows the specification of an IPv6
prefix in the form "-k prefix/prefixlen". If the prefix length is not specified, a
prefix length of "/128" is selected (i.e., the option assumes that a single IPv6
address, rather than an IPv6 prefix, has been specified).

-J SRC_ADDR, --block-link-src SRC_ADDR

This option sets a block filter for the incoming packets, based on their link-layer
Source Address. The option must be followed by a link-layer address (this option is
only valid for Ethernet interfaces).

-K DST_ADDR, --block-link-dst DST_ADDR

This option sets a block filter for the incoming packets, based on their link-layer
Destination Address. The option must be followed by a link-layer address (this
option is only valid for Ethernet interfaces).

-b SRC_ADDR, --accept-src SRC_ADDR

This option sets an accept filter for the incoming packets, based on their IPv6
Source Address. It allows the specification of an IPv6 prefix in the form "-b
prefix/prefixlen". If the prefix length is not specified, a prefix length of "/128"
is selected (i.e., the option assumes that a single IPv6 address, rather than an
IPv6 prefix, has been specified).

-g DST_ADDR, --accept-dst DST_ADDR

This option sets a accept filter for the incoming packets, based on their IPv6
Destination Address. It allows the specification of an IPv6 prefix in the form "-g
prefix/prefixlen". If the prefix length is not specified, a prefix length of "/128"
is selected (i.e., the option assumes that a single IPv6 address, rather than an
IPv6 prefix, has been specified).

-B SRC_ADDR, --accept-link-src SRC_ADDR

This option sets an accept filter for the incoming Neighbor Solicitation messages,
based on their link-layer Source Address. The option must be followed by a
link-layer address (this option is only valid for Ethernet interfaces).

-G DST_ADDR, --accept-link-dst DST_ADDR

This option sets an accept filter for the incoming packets, based on their
link-layer Destination Address. The option must be followed by a link-layer address
(this option is only valid for Ethernet interfaces).

--block-target, -w

This option sets a block filter for the incoming Neighbor Solicitation messages,
based on their Target Address. It allows the specification of an IPv6 prefix in the
form "-w prefix/prefixlen". If the prefix length is not specified, a prefix length
of "/128" is selected (i.e., the option assumes that a single IPv6 address, rather
than an IPv6 prefix, has been specified).

--accept-target, -W

This option sets a accept filter for the incoming Neighbor Solicitation messages,
based on their Target Address. It allows the specification of an IPv6 prefix in the
form "-W prefix/prefixlen". If the prefix length is not specified, a prefix length
of "/128" is selected (i.e., the option assumes that a single IPv6 address, rather
than an IPv6 prefix, has been specified).

--flood-targets, -T

This option instructs the na6 tool to send Neighbor Advertisements for multiple
Target Addresses. The number of different Target Addresses is specified as "-T
number". The Target Address of each packet is randomly selected from the prefix
fe80::/64, unless a different prefix has been specified by means of the "-t"
option. The IPv6 Source Address of each Neighbor Advertisement message is set
according to the IPv6 address or prefix specified with the "-s" option, and
defaults to a random link-local unicast address (fe80::/64) if the "-s" option is
left unspecified.

--flood-sources, -F

This option instructs the tool to send multiple Neighbor Advertisement messages
with different Source Addresses. The number of different sources is specified as
"-F number". The Source Address of each Neighbor Advertisement is randomly selected
from the prefix specified by the "-s" option. If the "-F" option is specified but
the "-s" option is left unspecified, the Source Address of the packets is randomly
selected from the prefix fe80::/64 (link-local unicast). It should be noted that
hosts are required to discard Router Advertisement messages that do not have a
link-local unicast address as the Source Address.

--loop, -l

This option instructs the na6 tool to send periodic Neighbor Advertisements to the
victim node. The amount of time to pause between sending Neighbor Advertisements
can be specified by means of the "-z" option, and defaults to 1 second. Note that
this option cannot be set in conjunction with the "-L" ("--listen") option.

--sleep, -z

This option specifies the amount of time to pause between sending Neighbor
Solicitations (when the "--loop" option is set). If left unspecified, it defaults
to 1 second.

--listen, -L

This instructs the na6 tool to operate in passive mode (possibly after attacking a
given node, if the ‘-d’ or ‘-D’ options were specified). Note that this option
cannot be used in conjunction with the "-l" ("--loop") option.

--verbose, -v

This option instructs the na6 tool to be verbose. When the option is set twice,
the tool is "very verbose", and the tool also informs which packets have been
accepted or discarded as a result of applying the specified filters.

--help, -h

Print help information for the na6 tool.

EXAMPLES


The following sections illustrate typical use cases of the na6 tool.

Example #1

# na6 -i eth0 -d fe80::1 -t 2001:db8::1 -c -o -e

Use the network interface "eth0" to send a Neighbor Advertisement using a random link-
local unicast IPv6 Source Address and a random Ethernet Source Address, to the IPv6
Destination address ffe80::1 and the Ethernet Destination Address 33:33:00:00:00:01
(selected by default). The target of the Neighbor Advertisement is 2001:db8::1, and the
message has both the "Override" and the "Solicited" flags set. The Neighbor Advertisement
also includes a target link-layer address option that contains the same Ethernet address
as that used for the Ethernet Source Address of the packet.

Example #2

# na6 -i eth0 -j fe80::1 -j 2001:db8::/32 -W fe80::/64 -c -o -e -L -v -v

Listen for incoming Neighbor Solicitation messages on the interface "eth0". Discard those
messages that have an IPv6 Source Address equal to fe80::1, an IPv6 Source Address that
belongs to the prefix 2001:db8::/32, or a Target Address that does not belong to the
prefix fe80::/64. Respond (to those messages that are accepted) with a Neighbor
Advertisement with a randomized Ethernet Source Address and a randomized link-local
unicast IPv6 Source Address (unless the Destination Address of the Neighbor Solicitation
was a unicast address), the IPv6 Destination Address set to the Source Address of the
incoming NS message (unless it was the unspecified address), the Target Address set to the
same value as the Target Address of the incoming NS, and the "Solicited" and "Override"
flags set. Be very verbose ("-v -v" options).

Use na6 online using onworks.net services


Free Servers & Workstations

Download Windows & Linux apps

  • 1
    Eclipse Tomcat Plugin
    Eclipse Tomcat Plugin
    The Eclipse Tomcat Plugin provides
    simple integration of a tomcat servlet
    container for the development of java
    web applications. You can join us for
    discussio...
    Download Eclipse Tomcat Plugin
  • 2
    WebTorrent Desktop
    WebTorrent Desktop
    WebTorrent Desktop is for streaming
    torrents on Mac, Windows or Linux. It
    connects to both BitTorrent and
    WebTorrent peers. Now there's no
    need to wait for...
    Download WebTorrent Desktop
  • 3
    GenX
    GenX
    GenX is a scientific program to refine
    x-ray refelcetivity, neutron
    reflectivity and surface x-ray
    diffraction data using the differential
    evolution algorithm....
    Download GenX
  • 4
    pspp4windows
    pspp4windows
    PSPP is a program for statistical
    analysis of sampled data. It is a free
    replacement for the proprietary program
    SPSS. PSPP has both text-based and
    graphical us...
    Download pspp4windows
  • 5
    Git Extensions
    Git Extensions
    Git Extensions is a standalone UI tool
    for managing Git repositories. It also
    integrates with Windows Explorer and
    Microsoft Visual Studio
    (2015/2017/2019). Th...
    Download Git Extensions
  • 6
    eSpeak: speech synthesis
    eSpeak: speech synthesis
    Text to Speech engine for English and
    many other languages. Compact size with
    clear but artificial pronunciation.
    Available as a command-line program with
    many ...
    Download eSpeak: speech synthesis
  • More »

Linux commands

Ad